Posts by Olin Lathrop
At first glance, your design looks reasonable. I assume D1 and D2 are really supposed to be on opposite data lines, and them both being on the A line is a typo? One thing that sticks out to me is...
Is there a scientific way to estimate the resistance of a pogo pin? Ultimately there must be, but it generally requires knowing things you don't know. Worrying about the resistance of the barrel ...
There are four things we can do with bad or poorly written questions. In order of seriousness, these are: Leave a comment. Downvote. Close. Delete. The questions you mention have mostly bee...
Is the answer of 1/c seconds correct It can't possibly be. The question is looking for a time value. "C" is a speed, which has units of distance/time. "1/c" therefore has units of time/distance...
What you ask is not specific to the Electrical Engineering site. There is nothing we can do about it here. If you really think this is a good idea, then you should propose it on the main Codidact...
Your question is impossible to answer without carefully looking at the layout and schematic. However, from gut feel and experience, this smells like poor grounding design. Common mistakes: Not a...
Digital voltmeters generally display decimal digits. The resolution implied by that is not necessarily the same as the underlying binary A/D. Since voltmeters for human display don't need to be f...
It's still unclear what you are really asking, so I'll discuss the tradeoffs between low and high side switching of power to a load. Low side switching The main advantage of low side switching is...
A differential amplifier and a differentiator are two completely different circuit blocks. Differential Amplifier A differential amplifier has two inputs and one output. It takes the difference ...
Personally I'd rather have everyone use their real name and affiliation. That basically puts their reputation out there on anything they say. If you really believe in something, have the guts to ...
Not a diff amp Something doesn't make sense here. You want A1A to act as a differential amplifier, but that's not how you wired it: Here is a real diff amp: Note how the right side of R1 is...
It could be OK if you are asking about technology reasons why a class of products will be phased out. Asking about forces that cause similar things in the past should be OK too, as long as the rea...
In addition to what Lundin said, making ACK dominant means that something out there is actively responding, and that response is affirmative. If ACK were recessive, then the transmitting node bein...
It's not completely clear, but it seems you are asking about a circuit in a class 1 div 2 location that will drive another circuit in a class 1 div 1 location. The point of the IS barrier is to pre...
The worst case won't get any better, whether series, parallel, or some other combination. The result of two 1 kΩ ±5% resistors in series is a 2 kΩ ±5% resistor. The probability that the result is ...
I've heard that input signals to digital circuits should be "de-bounced", at least sometimes. What is de-bouncing? Why is it needed? When is it needed? What is bouncing around in the first place?
in my engineering curriculum .. I never found a diode in a mosfet symbol Then you should ask for your tuition back, or perhaps the institution should want their diploma back. but in datasheets ther...
If I have a filter stage between an antenna and an LNA, wouldn't I want the load impedance(input to the LNA) to be large with respect to the source(antenna) in order to not attenuate the signal ev...
You are asking for a filter that passes 2% at 60 Hz and 99% at 90 Hz. That comes out to a transition of 97% of the amplitude within 0.6 of an octave, which is quite aggressive. The real answer My ...
A "normal" digital output actively drives both high and low. Open drain or open collector outputs only actively drive low, and go to high impedance when the signal is meant to be high. Some reaso...
That circuit doesn't do what you think it does. Here is the circuit in question: The impedance seen at IN is definitely higher at high frequencies, but that is only due to it being artificially l...
It's not clear whether you are asking about what the capacitor does in a buck converter, or how a capacitor works internally. I'll therefore go with: I am having a difficult time picturing the flo...
Calling those "registers" might be technically correct, but rather misleading in my opinion. These are really RAM locations. Probably for historical reasons, Microchip refers to RAM bytes in some...
Why do the Darlington or Sziklai configurations need complementary transistors? They don't. In fact, it's usually not even desirable. However, before we get too far, let's make it clear what we ar...
Here is the circuit in question, with the component designators changed to make them easier to write: To understand this circuit, try building it up in pieces. First, let's only include R1 and R2....