Communities

Writing
Writing
Codidact Meta
Codidact Meta
The Great Outdoors
The Great Outdoors
Photography & Video
Photography & Video
Scientific Speculation
Scientific Speculation
Cooking
Cooking
Electrical Engineering
Electrical Engineering
Judaism
Judaism
Languages & Linguistics
Languages & Linguistics
Software Development
Software Development
Mathematics
Mathematics
Christianity
Christianity
Code Golf
Code Golf
Music
Music
Physics
Physics
Linux Systems
Linux Systems
Power Users
Power Users
Tabletop RPGs
Tabletop RPGs
Community Proposals
Community Proposals
tag:snake search within a tag
answers:0 unanswered questions
user:xxxx search by author id
score:0.5 posts with 0.5+ score
"snake oil" exact phrase
votes:4 posts with 4+ votes
created:<1w created < 1 week ago
post_type:xxxx type of post
Search help
Notifications
Mark all as read See all your notifications »
Q&A

My grid dip: how does this electron tube technology work?

+0
−0

Here is a video of the AN/PRM10, and here is a schematic (I believe the image can be zoomed):

an/prm10

As most commercial grid dip meters produced in the past, this one possesses several functions in addition to the grid dip function. One of these is the "absorption type wavemeter", that allows to measure the frequency of an incoming signal. Here is what they say in the doc: gd2

I'm interested only in the tuning head part (the right box in the above schematic). In fact, I am only interested in understanding the "absorption wavemeter" function, that is, whenever switch S-103 is in diode position (the grid dip function is easier to understand and is not the subject here). Basically, the electron tube acts as a diode, which together with the network formed by the Z-201 coil and the tuning cap, forms a basic resonating detector. But I don't understand how the current flows and how this works.

two important points that took me a while to understand:

  1. in diode position, switch S-103 connects the top wire to the earphone jack, which is in fact a connection to ground: only when the earphone is plugged in, the jack disconnects from ground (by mechanical pressure) and then connects to the the 4k earphone impedance. Anyway, the earphone is not needed for the normal absorption wavemeter function: only micro ammeter M-201 is used. So, basically the top wire is connected to ground and is not powered. Only the filament of the electron tube is powered.

  2. I was told that the grid of the electron tube is able to self biase (to a negative potential) whenever the filament of the tube is warmed.

N.B: The whole documentation of the grid dip can be found Here.

History
Why does this post require moderator attention?
You might want to add some details to your flag.
Why should this post be closed?

1 comment thread

General comments (5 comments)

1 answer

+1
−0

The video helped explain a few things, but it's still not clear what the overall purpose of this device is. You showed it clearly producing a signal, but the documentation you quote talks about an incoming signal. The meaning of the current shown on the meter is unclear, and so is the function of the diode/osc switch. Because of all these things, I'm only going to answer very generally.

At first glance, this circuit seems to be using tube V-201 in a most unusual way. It's a JAN-955, which I'm not familiar with and didn't look up. Perhaps this tube is specifically designed for this unusual mode of operation.

It seems what is happening is that the thermionic effect is being used to create a current, which in fact seems to be the only power source for the oscillator. When you heat something to high enough temperature, electrons at the surface move so fast that they sometimes fly off. If they then hit something colder, so they won't fly off again from there, a net stream of electrons flows from hot to cold.

Electron tubes work on this principle by easily allows electrons to flow from the hot cathode to the cold anode, but making it pretty much impossible for electrons to flow in the other direction. That's a basic diode.

In a normal amplifier tube, forward current is encouraged by holding the anode at a positive potential relative to the cathode. The grid voltage can reduce this current by decreasing or even inverting the E field near the cathode. Since the grid is usually held negative relative to the cathode, it doesn't draw any current (the boiled-off electrons won't land on it since they are repelled by the grid's voltage). The result is power amplification. A few volts change at high impedance on the grid can control a substantial anode current.

Your device is using the temperature drop from cathode to anode as a power source. Electrons boil off the hot cathode and land on the cold anode, causing a current. Note that since electrons are negatively charged, the current is actually flowing in to the anode and out the cathode. The anode in your circuit is actually held at negative voltage, powered by the tube itself.

The grid still works to modulate this current. Note that a parallel tuned tank circuit is connected between the plate and grid. This feedback, together with the power provided by the tube itself, forms an oscillator. The tuning knob adjusts the capacitance part of the LC resonant circuit, and the inductance part is changed by selecting different plug-in modules. As a result, this oscillator can be tuned over a wide range of frequencies.

The meter seems to be showing some measure of the plate current. Note that the + side of the meter is tied to ground.

The cathode of V-201 is tied to ground via an inductor. That makes the power supplied by the tube high impedance at high frequencies.

With the high impedance, and the oscillator coil deliberately external to the case, small external signals at the oscillator frequency will have significant and measurable effects on the oscillator. It appears that is the point of this device, which is to measure external fields by how they perturb this very sensitive tuned oscillator.

History
Why does this post require moderator attention?
You might want to add some details to your flag.

1 comment thread

General comments (1 comment)

Sign up to answer this question »