newbie
A quiet enigma. We don't know anything about newbie yet.
Posts
See all 40 »When downloading a Manufacturer Part Number (MPN) directly from Altium Manufacturer Part Search, I often see multiple footprint options available for the same component: IPC_A IPC_B IPC_C MFG (...
2 answers · posted 5mo ago by newbie · last activity 5mo ago by Nick Alexeev
I need to interface a radiation sensor (BG51 by Teviso Sensor Technologies) with TTL output with a CC1352P microcontroller. May I know how to approach this.
3 answers · posted 12mo ago by newbie · last activity 4mo ago by TonyStewart
The below circuit is take from here. May I know how this circuit maintains the Potential at Reference Electrode and Working Electrode same. Here you can see that the working electrode is connec...
1 answer · posted 1y ago by newbie · last activity 1y ago by Olin Lathrop
Basic Explanation of my System: The proposed design is a battery-powered wearable device that integrates advanced sensing and power management features. The system operates primarily from a single...
1 answer · posted 9mo ago by newbie · last activity 9mo ago by Olin Lathrop
I’m using an Infineon TLE4973 current sensor. It has a DCDI pin, which the datasheet describes as a single‑wire, open‑drain, UART‑based interface (master–slave). It specifies logic thresholds (LOW ...
1 answer · posted 7mo ago by newbie · last activity 7mo ago by Olin Lathrop
I am working on a rigid-flex design with two ICs placed on different rigid sections: an MCU on one board an AD5941 on another board The two rigid sections are connected by a flex PCB. This is a 4...
2 answers · posted 5mo ago by newbie · last activity 5mo ago by Lundin
I have an ADC board. This board will communicate with a STM32 develoment board via SPI interface. I am using jumper cables for connecting the ADC SPI lines to ST32 evaluation board. Below is my AD...
1 answer · posted 8mo ago by newbie · last activity 8mo ago by Olin Lathrop
Basic Explanation of my System: The proposed design is a battery-powered wearable device that integrates advanced sensing and power management features. The system operates primarily from a single...
1 answer · posted 10mo ago by newbie · last activity 10mo ago by Olin Lathrop
I am making a breakout board which contains 4 hall effect sensors from paragraf.The sensor P/N is EGHSX03Q02 .My schematic is given below .Like this 4 sensors placed in the pcb. These sensors are ...
1 answer · posted 1y ago by newbie · last activity 1y ago by Olin Lathrop
I am using AD5941 in my design. The power section of its analog domain (AVDD) is given below. It is obtained from the reference design. You can see the schematics, BOM etc in bottom of this page. ...
2 answers · posted 1y ago by newbie · last activity 1y ago by Nick Alexeev
I am using an IR transceiver in my design.This IC is working at 3.3V supply.This IC need not be on always so I decided to give a control to it's shut down pin (Pin no 5,Shutdown Input. Active low)....
1 answer · posted 2y ago by newbie · last activity 2y ago by Olin Lathrop
The below image is taken from Analog Devices design note DN1045. what is the use of M1 and M2? What is the use of REF and D1?
1 answer · posted 1y ago by newbie · last activity 1y ago by Nick Alexeev
I am using OPA859-Q1 in one of my applications. It's supply voltage is 3.3V,single supply operation.I am confused about is output swing when operated from 3.3V supply Is the maximum swing is 2.4V ...
2 answers · posted 1y ago by newbie · edited 1y ago by Olin Lathrop
