Posts tagged current
I have a small solar panel rated for 6V/DC, 150mA. I know that those specs are under ideal circumstances, and I would like to do some measurements in different weather conditions to see what I can ...
In this circuit below the relay circuit part is acting as an inrush current limiter, but I can't understand how it works since the current is flowing in both conditions where the relay is open or c...
I've heared that arc welding is getting done with low voltage. As I know arcing requires high voltage. The how arc welding is done with about 50 volt. In my opinion I've thought we need kilovolts f...
Suppose we have this graph: How can we find the operating point (Q)?In common emitter collector we just draw a line from the vertical axis (Ic) at the point (0,VCC/RC) to the horizontal axis a...
I was studying the Re model of a transistor: But the Re model for 2 different configurations (common emitter and common base )turns out to be the same! I don't know why I am really confused.How...
I have designed a graph of the current in a photoresistor related to the brightness of light which hits the photoresistor. Our professor told us that it is more correct to draw the Current/Brigh...
In this datasheet it says that the minimum resolution is 0.1uA for the 10mA range.What is this minimum resolution?Is it the sensitivity of the multimeter for the 10mA range?
Can we find the internal resistance of a multimeter ,when we use the multimeter like a ampmeter, from its datasheet? I am trying to find the internal resistance of IDM 505 and I went to the datash...
Intro Hi everyone, I have a question about the practical use of a PTC (positive thermal coefficient) resettable fuse. I've never used one before, but I'd like to add one to a DC motor circuit to p...
In monostable multivibrators we use a trigger signal applied to the base of the transistor which is usually off to enter the astable region Can we instead have a pin which is connected directly ...
How to find the equation of current of the RLC circuit after the switch is moved?
Which will be the total series inductance?
How do I find the current through the inductor and the voltage of the inductor after the switch is closed?
How do I find the voltage of the capacitor and the current through the capacitor after the switch is closed?
Suppose we have this circuit How do I pick a appropriate value for the resistor R1?
The current through the tunnel diode is: where $I_{f}$ is the current from the Shockley diode equation and $I_{tunnel}$ is the tunnel current. Is there an expression for the tunnel current or i...
Moderator's note: This is getting ridiculous. You keep posting these drawings that are barely legible. The scribbling is bad enough, but the uncropped images are unacceptable. The image you ori...
Is this equation valid only when a JFET in saturation mode , correct? because in the ohmic region the JFET acts like a voltage controlled resistor and increase in VDS increases the resistance of th...
I have a question about this circuit:(critically damped oscillation) For a critically damped oscillation for a series RLC circuit the equation of current has this form I(t)=D1te^(-at)+D2e^(-at) ...
I find the current flowing through the capacitor $$\begin{align} I_{C_1}(t)&=\dfrac{\mathrm{d}}{\mathrm{d}t}\left[V_1(t)-I_{C_1}(t)R_1\right] \\ {}&= \dfrac{\mathrm{d}}{\mathrm{d}t}\left...
How can we find the equation of current and voltage of a capacitor circuit if the input voltage is AC without using the impedance formula Xc = -jωC?. We have for homework to find the equation of...
I'm trying to modify a LED torch, and there is a DC-DC booster (1.5 V to 3.3 V) and after that some SOT-23 device which (I assume) keeps constant 90 mA current through LED. I know I could remove th...