Search
The question below was raised by a "new user". The identity of the "new user" was deleted because it was found to be an alias of an already suspended user: - So, why is the question still active...
If there isn't a VA rating on the label or published in a reliable source, then you have to guess. There are several clues that can be used: Look at the size of the primary wires. That gives you...
I have a HANTEK 6022BE oscilloscope and I'm monitoring three signals with it: FS (Frame sync clock). Pulse. Transfer complete. I'm using two channels of the scope to monitor a pair of these...
This picture describes the behaviour of a single phase transform under resistive,inductive and capacitive loads(from left to right) How what exactly is $V_{1}$ ?Is it the voltage at the primary ...
I have a MOT that is rated 220V-50Hz only and i need to know its maximum operating power i tried to google the reference number but unable to find anything about its power, so how to figure out the...
Question 4 solved: The datasheet lacks the information I've copied from PCM5122:
What we call this opamp configuration? A mess. What's the advantage and the disadvantage of this circuit? This can't be judged without the stated objectives. It might be useful for keepi...
I have been reading about thermal noise in resistors and I have a question: Suppose we have this circuit: Is C2 here to protect the voltage source from thermal noise?
I think these kind of abstract/big picture data communication questions should be on-topic here. Such as the mentioned question about the OSI model. I've been actively pushing for software.codidac...
This is someone trying to rehash a Light experiment with circuits, however I do not think it holds up. Inside a medium, charged particles are subject to Drift Velocity. When you work through the ca...
In this datasheet it says that the minimum resolution is 0.1uA for the 10mA range.What is this minimum resolution?Is it the sensitivity of the multimeter for the 10mA range?
Hello everyone, I have a simple circuit in which I control some LEDs via an MCU and DMG2302UK ( N-channel MOSFET ) The EN pin is connected to an MCU gpio pin that works at 3.3V. The circuit wo...
Assuming we have a voltage regulator : Why do we have to ground Vin and Vout using 2 capacitors just like that?Co could be to provide a low resistance path to GND at high frequencies but what is...
I must admit that your question (the described problem) is an interesting one. Speaking about the circuit (without consideration of the parts values), there are two feedback effects: At first, ...
Based on very little information and you just starting PCB layouts, you may be overthinking this problem or rightly concerned. There are a lot of fundamentals you might already know about how to m...
My Altec Lansing speakers sometimes bleat out a weird sound. It's usually something like "dit. dit-dah-dit. dit-dah-dit." I suspect it has something to do with radio traffic from my computer or ph...
I have a differential signal source and a single source amplifier. The source has 2Vp-p signal. I wanted to center the differential signal around 2.5V, so I came up with the following circuit: S...
This is an expansion on Biasing a differential opamp input post. Olin pointed out that gotchas can be in the implementation, so I will provide the circuit and design specifications as well as my re...
None of these ideas optimize the SNR that you need. You need to design with error correction or (suppression); 50V/m grid E-field (Right Led Drive RLD) >100 dB suppression AM radio noise (...
I am working on a digital output concept that I would like to have the following characteristics: Output voltage swing: 0 to 5V Controllable by the uC from 3.3V power supply I would like to be...
I see and from the photo left to right , the 3 regulators are ; +15, -15 , + 5.0 LM324-15 LM320-15 LM324-50 The +ve LDO's share the same heatsink with insulator + plastic screws. To...
I'm in the process of giving the tags page some structure, writing tag descriptions and creating synonyms and some hierarchy. I'd like to know the Community stance on a new tag I'd like to add: b...
I would like to convert 5V rail I have on PCB to ±12V. Existing solution is using boost converter 5V to 12V, and a buck for 5V to -12V. This feels bulky for what it's needed - here are the requirem...
As of the early 2020s, common technology nodes for SSI (Small-Scale Integration) and MSI (Medium-Scale Integration) ICs include nodes such as 180nm, 130nm, 90nm, 65nm, 45nm, and 28nm. Each technolo...
