Search
Apart from correcting capitalization, which is a valid change, I think you are at the same time doing a lot of subjective changes to certain tags and it can get very intrusive on the site. I don't ...
In both cases, is the "X" point floating when there is no 12V applied ?
I'm Interested In Power Circuit. What Courses/Guidelines To I Need To Properly and Effectively Under Power Circuits??
I've tryed to implement a local ground concept told by Olin Latrop here : He have told: (What I've perceived)You should not connect every gnd point instantly to gnd plane, since it can inject HF ...
Mini-circuits LNA PHA-LN13+ has suggested: Eval board Layout Eval Gerber The image took from the Gerber file (3rd ref.) (Though all 3-reference mentioned containing it): There I have som...
The output collector-emitter part of a transistor can be thought of as a 2-terminal SPST switch controlled by the input base-emitter voltage or base current. So this transistor switch can control o...
I am trying to test a AD8307. Here are my connections: (pins not shown are left unconnected, and also pin 8). I get a quiescent output voltage at pin 4 of about 850 mV with respect to ground, w...
Please see the image below. I'm trying to convert my IKEA NYFORS floor lamp into a reading light, by covering the top with an Aluminium pie plate. Will this be a fire or electrical hazard? Does an...
Im designing a high-pass filter which has a gain of -8dB at half of the roll-off frequency and I am stuck ,I dont know how to continue the design. In the bode plot of that filter we have 2 points:...
If I connect a battery to an LC tank and then to an antenna and then on the other side at a distance x, I connect an antenna to another LC tank and this to a diode and this to an LED, Do a I have a...
It all depends on the values of the components:If the system will very slowly decay until the energy of the system reaches 0. If the system undergoes something which will look like a part of...
When 2 inductors share the same magnetic field they become coupled and besides their self inductance they have a mutual inductance as well. For this circuit: Now current entering one coil marke...
I have this circuit: I think that R3 acts like a feedback path from the output to the input.However I am not sure what will happen if I change the value from 100Ohms to lets say 1kOhms. I have ...
I have learnt that if we have 2 parallel conductive plates and we seperate them the capacitance is increased if we put a good conductor between the plates. Now the resonant frequency of a inductor...
How do I find the current through the inductor and the voltage of the inductor after the switch is closed?
The thermal stability coefficient is defined to be: $S = \frac{dI_{C}}{dI_{CBO}}$ where $I_{CBO}$ is the reverse current of the BJT when voltage isnt applied to the base of the BJT. In case of a ...
I may be a little bit biased on this one because it was my question which started this thread but : I don't think data communication question should be generally off-topic because it evolves binar...
In a 3 phase Star source-Star load circuit the phase voltage has different phase than line voltage and in a 3 phase Delta source-Delta load circuit the phase current has different phase than the li...
We have to maintain the focus of the Electrical Engineering board at the electrical engineering level. We will be inundated by laymen questions (electronics use, repair, explaining electronics to ...
Thanks for asking. Repair questions are off-topic, in general. We may consider a repair question, if you explain your specific troubleshooting steps, and you understand the design of the device....
Looking for KalleMP who last commented on the link attached. https://electronics.stackexchange.com/questions/368517/remotely-monitor-condition-of-fuse#:~:text=R1 %26 the LED are the basic indicato...
Moderator's note: This is getting ridiculous. You keep posting these drawings that are barely legible. The scribbling is bad enough, but the uncropped images are unacceptable. The image you ori...
We identify semiconducting electrical components this way: The first digit represents the number of pn junctions inside the semiconducting device The two or more digit number starting at position...
My mistake was taking the third relationship $$ \frac{1}{RC} $$ which says how to find the bandwidth of a parallel RLC filter but we have a series RLC filter. Now solving the system : $$ LC = 100...
Instead of using a buck or a boost converter can we use for DC-DC conversion the circuit Im going to describe in the next lines? First we begin with a Hartley oscillator whose output is fed into ...