Posts tagged voltage
Usual values used in doing electronics/power supplies are almost always round numbers: 5V 12V 28V 48V 60V I understand that in some cases ICs are built to accept the voltage directly comi...
Instead of using a buck or a boost converter can we use for DC-DC conversion the circuit Im going to describe in the next lines? First we begin with a Hartley oscillator whose output is fed into ...
I was looking for guidelines of how to select appropriate cables for applications (I am interested in DC), I found IEC 183 standard which talks about high voltage cable selection for AC. Also, the ...
In a previous question we found that for a critically damped oscillation: $$ I(t) = 2 t e^{-0.5 t} $$But if we integrate to find the voltage through the capacitor: $$ V_{CO} + \frac{1}{C} \cd...
Inside a op-amp after the stage where the differential signal is converted to single ended , there is further amplification of the DC signal.For AC signals there is a capacitor parallel to the tran...
During the open circuit test of a induction motor ,not any current flows inside the rotor.But how can we achieve such a thing? Here is the ping configuration of a induction motor: The coils of ...
This picture describes the behaviour of a single phase transform under resistive,inductive and capacitive loads(from left to right) How what exactly is $V_{1}$ ?Is it the voltage at the primary ...
We use a DC externally excited generator/motor as a generator.We excite the input of the generator and get at the output 10V at 1Wb flux and at 5rps generator speed without connecting the generator...
I've heard that arc welding is getting done with low voltage. I believe arcing requires high voltage. Then how is arc welding done with about 50 volts? I thought we need kilovolts for arcing. Why? ...
Im designing a high-pass filter which has a gain of -8dB at half of the roll-off frequency and I am stuck ,I dont know how to continue the design. In the bode plot of that filter we have 2 points:...
I want to find the conditions of oscillation of the following Hartley oscillator.I have attached a load (ZL) to my Hartley oscillator I have written KCL for nodes A,B: For node A: $$\frac{V_{A...
Im designing a Hartley oscillator this time with a opamp providing the open-loop gain.I have tried drawing the small-signal analysis of my circuit to use KVL and KCL to find the conditions of opera...
The small signal analysis of a BJT when the BJT is in amplification mode: is easy.However what happens when the BJT is in saturation mode? Can we replace the dependent current source with a r...
I am trying to find the AC analysis of a BJT Hartley oscillator but I cannot continue. How do I find the voltage gain? When no feedback is there, we just find the output resistance and the current...
I am designing a low-pass filter with cut-off frequency = 100Hz and after the cutoff frequency from -3dB to -10dB the average decrease in db/Hz = -0.1 db/Hz.I know how to design a low-pass filter ...
I was studying the Re model of a transistor: But the Re model for 2 different configurations (common emitter and common base )turns out to be the same! I don't know why I am really confused.How...
In this datasheet it says that the minimum resolution is 0.1uA for the 10mA range.What is this minimum resolution?Is it the sensitivity of the multimeter for the 10mA range?
Can we find the internal resistance of a multimeter ,when we use the multimeter like a ampmeter, from its datasheet? I am trying to find the internal resistance of IDM 505 and I went to the datash...
A while ago I made a question about the monostable multivibrator .Lets get a picture of it: When switch is closed it enters its unstable state and it eventually returns to the stable state Howe...
Assuming we have a voltage regulator : Why do we have to ground Vin and Vout using 2 capacitors just like that?Co could be to provide a low resistance path to GND at high frequencies but what is...
I have this circuit: I think that R3 acts like a feedback path from the output to the input.However I am not sure what will happen if I change the value from 100Ohms to lets say 1kOhms. I have ...
Hello I don't understand how this differential to single-ended voltage converter can work. What I don't understand is why we place a current mirror(a current mirror copies the current flowing thr...
In monostable multivibrators we use a trigger signal applied to the base of the transistor which is usually off to enter the astable region Can we instead have a pin which is connected directly ...
How does the differential to single ended converter work? In order for the circuit to work, Q1 and Q3 must be in the saturation region and depending on the voltage inputs, one of Q2 and Q4 will be...
How do I find the current through the inductor and the voltage of the inductor after the switch is closed?
How do I find the voltage of the capacitor and the current through the capacitor after the switch is closed?
In this bistable multivibrator which is $Q$ and which is $\overline{Q}$?
Moderator's note: This is getting ridiculous. You keep posting these drawings that are barely legible. The scribbling is bad enough, but the uncropped images are unacceptable. The image you ori...
Is this equation valid only when a JFET in saturation mode , correct? because in the ohmic region the JFET acts like a voltage controlled resistor and increase in VDS increases the resistance of th...
How can we extract a DC signal from a mixed signal?If we want to extract the AC component of a signal we can use a blocking capacitor to remove any DC offset but how do we achieve the opposite?Can ...
I find the current flowing through the capacitor $$\begin{align} I_{C_1}(t)&=\dfrac{\mathrm{d}}{\mathrm{d}t}\left[V_1(t)-I_{C_1}(t)R_1\right] \\ {}&= \dfrac{\mathrm{d}}{\mathrm{d}t}\left...
How can we find the equation of current and voltage of a capacitor circuit if the input voltage is AC without using the impedance formula Xc = -jωC?. We have for homework to find the equation of...
