General Q&A about the design and function of electronic systems, electric power systems and infrastructure, their theory, and tools specific to those fields. Read these guidelines before posting.
Filters (None)
I'm designing remote controller based on NRF24L01 and STM32. I want to use SMA antenna. My question is regarding power amplifier (PA). When is it necessary to use one? The range I'm aiming for is 2...
The small signal analysis of a BJT when the BJT is in amplification mode: is easy.However what happens when the BJT is in saturation mode? Can we replace the dependent current source with a r...
EMG consists of an electrode gel skin interface, op-amps with a certain gain and an ADC. Question is in the context of passive electrodes. What are the essential safety features of such types of h...
If we have the transfer function of a LC high pass filter: $H(s) = \frac{sL}{sL+\frac{1}{sC}}$ If we want to find the pole of that filter in the end we get: $s = \frac{j}{\sqrt{LC}}$ and for a ...
Hi guys so recently i was looking for a mosfet and a gate drivers and between a lot of their specification the rise/fall time and Turn-On/off Delay Time sometime it called propagation. My question...
Hello, I am trying to use a CD4047 in monostable, positive-edge trigger mode: I am not skilled enough to make out what the output, i.e. pin 10, should be when pin 8, the input, is held at 0V (...
I am designing a low-pass filter with cut-off frequency = 100Hz and after the cutoff frequency from -3dB to -10dB the average decrease in db/Hz = -0.1 db/Hz.I know how to design a low-pass filter ...
I am planning to use the LM318 operational amplifier to generate a PWM signal and I need to know how to calculate the rise/fall time. LM318/LM218/LM118 datasheet -The slew rate is 70 V/µs maximum...
I have a non-invasive current sense transformer (SCT-013-030) which according to its datasheet it is voltage output type. I want to harvest energy and supply a wireless sensor that consumes 5-6 uA...
I understand that white noise is not always Gaussian. In general, is the $V_{pp}$ and $V_{RMS}$ noise stated in operational amplifier and ADC datasheets Gaussian? And is its mean zero? Any exemptio...
In both cases, is the "X" point floating when there is no 12V applied ?
We use a DC externally excited generator/motor as a generator.We excite the input of the generator and get at the output 10V at 1Wb flux and at 5rps generator speed without connecting the generator...
This question is related to my previous question. I want to drive a brushed DC motor using H-bridge. To power the motor two 18650 cells will be used in series. The issue is that I want to limit th...
I want 3 SMPS (AC-DC) : Vout/Iout - 5V/20A , 12V/75A , 24V/30A Vin (AC) ~ 220V/50Hz I want it such that I can use Hard & Soft Kill Switches for turning off. Can you help me with the same. I tho...
I am designing a control system controlled by some microcontroller K: The open loop gain is $G_{o}(s) = \frac{K}{s(s^{2}+4s+3)}$ and the closed loop gain is obviously $G_{c}(s) = \frac{K}{s(s^{...
The submarine built by OceanGate went missing on 18th June 2023. A lot of online criticism was directed towards the control hardware of the submarine - Logitech F710 controller. However, why i...
I have been watching this video and at 3:28 it says that a induction is inherently self-starting.Does this happen because of the energy stored and released in the windings of the statorFrom 3:41 u...
For high-speed digital communication busses, what attributes do you generally advise to add to a PCB to help with validating the communication bus as well as troubleshooting the design? In particu...
[Disclaimer. This is not for an academic class. I'm self-studying.] I’m reading an introductory book on DSP for audio and computer music [Steiglitz 1996, ISBN 0-8053-1684-1 p. 287]. One of the ...
Whenever declaring a variable in C outside a function at file scope or when specifying it as static, it gets assigned a life time known as static storage duration. Meaning it will be accessible thr...
When recording an ECG signal, the raw signal is taken from the body and sent into an ECG amplifier to amplify the signal to a suitable range and remove common mode and other types of noise. Measur...
I have a solar panel rated for 6V open-circuit and up to 150mA. I would like to connect this to an SPV1040 or similar buck-boost converter with MPPT functionality to be able to charge a 3.6V batter...
My scenario is this: radio equipment controlling an overhead crane inside a steel mill. Specifically it is used for transporting melting pots. With the current, unfortunate installation, the antenn...
I'm looking for input from anyone with insight in the PLC world. How do PLCs usually measure 4-20mA current loops? I would assume it's one of these two alternatives: Through an external "shunt"...
Hi guys, Can anyone help me please replace the NE555 IC in this circuit by MIC1555. I need to modify also the Voltage to 18v thank you. MIC1555 datasheet NE555 datasheet Edit: The circuit a...
I am generating files for manufacturing my design in Altium 22 and ordering through Eurocircuits. What I noticed during the ordering process is that the rotation of many components (and sometimes ...
As we know there exists numerous different kinds of PCB CAD software. The big ones seem to be Eagle, KiCAD, Altium, OrCAD, Solidworks, DesignSpark and probably a few more. When it comes to mechani...
I am an electrical engineering student and I just finished designing an ECG-amplifier circuit. Here is the schematic: - It is fairly simple. Initially, there is a 1st order highpass filter. Then...
I have a design of a power line communication using the following IC. https://www.yamar.com/datasheet/DS-SIG60.pdf My design is the same as the example circuit in the datasheet of the chip. Th...
I have a Rigol DS1104 oscilloscope. Last week I stood up quickly from my table and saw a spike on the scope. Right now all the channels have a DC offset when probe is connected to ground or unconne...
1- What we call this opamp configuration? 2- What's the advantage and the disadvantage of this circuit? 3- And what's the purpose of the L2 in the feedback? I have changed gradually the value of...
Instead of using a buck or a boost converter can we use for DC-DC conversion the circuit Im going to describe in the next lines? First we begin with a Hartley oscillator whose output is fed into ...
Im designing a high-pass filter which has a gain of -8dB at half of the roll-off frequency and I am stuck ,I dont know how to continue the design. In the bode plot of that filter we have 2 points:...
I saw that equation of reactance is written like this $$I=\frac{V}{|R+X_L j|}$$ $$I=\frac{V}{|R-X_c j|}$$ When there's capacitor and inductor in a single circuit then it is written like : $$I=\...
Assume that I have some generic antenna connector, followed by a pi-filter/50ohm impedance matching components, then a DC blocking cap (as per the RF switch recommendations) and then a RF switch fo...
I have a small solar panel rated for 6V/DC, 150mA. I know that those specs are under ideal circumstances, and I would like to do some measurements in different weather conditions to see what I can ...
I was looking at different transistors, especially MOSFETS and I saw that N type MOSFETs seem to be way more popular to be used in circuit design. Is there a reason for that, or am I mistaken?
This question is asked in an addition to https://electrical.codidact.com/posts/276436 Here is a Flyback converter mentioned there: Design parameters are: Input voltage 125 volts Output volt...
The premise In a recent video by the pop-sci channel Veritasium, the concept of the flow of electricity and energy transmission in a circuit was discussed. In that video a thought experiment is pr...
RF novice here. If using a superheterodyne receiver for the purpose of FM/FSK modulated signals, I'm wondering if the location of an optional automatic gain control (AGC) circuit is always placed o...
According to Signal processing and linear systems by Lathi, the transfer function $H(j\omega)$ does not exist for systems with poles in the RHP: - This makes sense to me, since $H(j\omega) = \fr...
A taper pad is a resistive attenuator that maintains impedances on both ports and provides a specific amount of gain-loss ($A_{12}$): - I have derived formulas for each resistor (that I know to ...
I was watching a video from EEVBLOG about bypass capacitors, and he presented a theory that randomly connecting different values of capacitors in parallel can create unexpected impedance spikes: ...
Before the circuit here are the digital blocks which have been already designed and exist as part of the division block 1 bit subtractor: 2 bit subtractor(in the digital block diagram of the di...
Suppose we have a RC low pass filter of 1st order. If we add multiple stages every time we add a RC stage identical to our original does the slope of the curve in the bode plot db/Hz becomes wild...
Suppose we have this stream of data.Let's assume the data stream lasts 1 sec. How do we find the bandwidth of the data?Do we Fourier transform the signal in order to find its components in the ...
Suppose we have this graph: How can we find the operating point (Q)?In common emitter collector we just draw a line from the vertical axis (Ic) at the point (0,VCC/RC) to the horizontal axis a...
There are various different methods to keep common mode currents off the cables, one of them being discussed on the site here and with Olin's decoupling caps post on StackExchange. Slight digressio...
Signals with frequency above the cutoff frequency of a transmission line cannot be transmitted through the transmission line. But how can I calculate the cutoff frequency of a single phase transm...
Which important system design parameters need to be locked in order to estimate the maximum allowable level of the input voltage ripple of an SMPS? I have encountered ballpark figures of <1%, &...